Product Description
Introduction
Static mixing vacuum casting plant is mainly applied for 35KV and below epoxy resin casting of dry type transformer,transformer ,reactor , high voltage switch insulator ,which can also meet the epoxy resin coating power and the vacuum casting of electronic components .
Structure
1. Vacuum casting tank : According to the use of points divided into two round and rectangular, according to different processes have a vacuum - pressure and vacuum-type, manual or automatic casting.
2. Material handling system: Improved film degassing and mixing technology, better and easier prolapse of moisture and air in the material. All chambers configured on the interface are standardized, not only interchangeable, but also to facilitate the future upgrading of equipment.
3. Material mixed metering system: According to the level of automation is divided into static and dynamic mixing two kinds of materials.
4. Vacuum system: The main vacuum pump group, vacuum filters, vacuum valves, pipes and other components.
5. Heating system: Casting chamber currently used electric heating plate directly heated. Mixing chamber indirect heat conduction oil, material conveying pipe with constant temperature with tropical insulation
6. Pneumatic system: Compressed air source, control valve, pressure detection system and other components for the vacuum, material valve control.
7. Cooling water system: Mainly used for cooling of some vacuum pumps and condensers. At present, our company has developed a
casting plant that does not require cooling water.
8. Control system: For the control of the entire system operation, simple system without filler direct control by the relay. Programmed control by PLC-PC with metering or static mixing, according to process requirements, control of vacuum degree, temperature regulation and casting process, and the linkage protection and interlocking of each action to avoid human error. Have a detailed record of all operations, have been prepared to find. You can also set different operating rights to ensure the safety of plant and products.
9. Other parts: The processing unit of the silica powder can be configured according to customer requirements, including the transportation and preheating and drying of the silica powder and the pre-mixing pre-degassing with the resin or the curing agent, the silica powder and resin, the curing agent, the toughening agent formulation and static mixer staticcooling device.
10. Our company produced the small electronic components of the epoxy automatic potting equipment, high degree of automation, dose error of less than 5%, accurate mold positioning. Casting part of the configuration of 1-5 casting head, casting can be synchronized to achieve continuous flow-type production.

Vacuum Casting Equipment Specifications
casting tank size
(mm)
limit vacuum
(Pa)
working pressure
(Mpa)
measuring type
controlling
φ2000 x2200
≤50
≤0.4 or normal pressure
electronic scale
PLC + touch screen
φ2400 x3000
≤50
≤0.4 or normal pressure
electronic scale
PLC + touch screen
φ2500 x3500
≤50
≤0.4 or normal pressure
electronic scale
PLC + touch screen
φ3000 x3500
≤50
≤0.4 or normal pressure
electronic scale
PLC + touch screen
φ3200 x3500
≤50
≤0.4 or normal pressure
electronic scale
PLC + touch screen






OPERATION PRINCIPLE
In the absence of air , through the different units of work ,dehydrating , degassing , heating to a certain temperature and
mixing proportional for casting material ,Then casting it to the coil in the mould in the whole vacuum environment .
FEATURES

The epoxy casting equipment product-ed is simple structure , convenient operation and easy maintain by our company ,which can also
meet various technical requirements , including filler or without filler . The versatile unit design can be matched flexibly and
can meet the requirements of upgrade in the future .

Detailed Images
Offer customization and field installation commissioning and training, Field maintenance and repair service,Free spare parts, Video technical support, online support, etc.




Size Information
Basic type vacuum pressure casting plant
Dynamic type vacuum pressure casting plant
Static type vacuum pressure casting plant
Casting Tank Dimension(mm)
Limited Vacuum Degree
Material Leakage Pa.L/s
Working pressure(Mpa)
Mixing Material
Control Type
1800*2000
≤50pa(no load)
≤100
≤0.4 or normally pressure
Dynamic or Static
Manual measuring or PLC Control
Pouring Type
Manual control
Related Products
Related Products
Full Automatic PLC Control Coil Winding Machine for Transformer
$29000.00 - 69000.00 / Set
China Manufacture Customization Industrial Hot Air Cycle Curing Oven
$9231.00 - 15385.00 / Set
China Professional Manufacture Vacuum Drying Oil Filling Plant of HV Instrument
$56790.00 - 110000.00 / Set
YQ250CM Wide Speed Selection Range Parallel Electric PT Coil Winding Machine
$8500.00 - 9000.00 / Set
Packing&Shipping
Semi-Automatic PET Bottle Blowing Machine Bottle Making Machine Bottle Moulding Machine
PET Bottle Making Machine is suitable for producing PET plastic containers and bottles in all shapes.




After Sales Service

Field installation, commissioning and training.
1. Free spare parts.
2. Field maintenance and repair service.
3. Video technical support.
4.Online technical support.
5. Wechat/What's app: +86 15979221627 in 24 online instant service for vaccum casting plant, Vacuum drying plant, Vacuum casting plant, Hot Air drying oven, Vacuum mixing equipment, APG clamping machine, APG mold & casting mold, Vacuum coating system,Vacuum annealing furnace plant,Vacuum pressure impregnation plant, Vacuum Oiling plant , Foil winding
machine , HV and LV winding machine, Automatic CT PT winding Machine, Automatic wire winding machine, Stereoscopic triangle core foil winding machine, Automatic stereoscopic core winding machine, Core cutting machine.
Company Introduction
Yibo is a professional manufacturer of electric power equipment integrating R&D, Production, Sales and after-sales technology guide and support.
From our side we can offer:
-Vacuum drying equipment
-Vacuum casting equipment
-Hot Air drying oven
-Vacuum mixing equipment
-APG clamping machine
-APG mould & casting mould
-Vacuum coating system
-Vacuum annealing furnace
-Vacuum pressure impregnation
-Vacuum refueling equipment
- Foil winding machine
-HV and LV winding machine
-Automatic CT/PT winding Machine
-Automatic wire-laying winding machine
-Stereoscopic triangle core foil winding machine
-Automatic stereoscopic core winding/cutting machine
YIBO has more than 29 years experience of this field.
For short overview please see:www.vacuum18.com



Our Services & Strength
Manufactuer one-stop machine and professional technical service & support for electrical production.
FAQ
Q: What information do we need before quote?
A: Your product’s diameter and photo or drawing.

Q: How about your installation & debugging and after-sale service?
A: Our engineer go to the oversea for the installation and debugging availably, and we provide one-stop service and machines
lifelong maintenance. On site test and inspection available.

Q: How about your experience in this field?
A: We have 29 years experience in this field. Until now, we have 20 items patents.

Q: Is it one -stop service company in electric power equipment industry?
A: Yes, Our products cover Vacuum drying plant
Vacuum casting plant
Hot Air drying oven
Vacuum mixing plant
APG clamping machine
APG mould & casting mould
Vacuum coating system
Vacuum annealing furnace-Vacuum pressure impregnation
Vacuum refueling plant
Foil winding machine
HV and LV winding machine
Automatic CT/PT winding Machine
Automatic wire-laying winding machine
Stereoscopic triangle core foil winding machine
Automatic stereoscopic core winding/cutting machine